View AP7361C-10_8410890.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ap7361c document number: ds 37274 rev. 2 - 2 1 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product 1a low dropout adjustable and fixed - mode regulator with enable description the ap7361c is a 1a, adjustable and fixed output voltage, ultra - low dropout linear regulator with enable. the device inc ludes pass element, error amplifier, band - gap reference, current limit and thermal shutdown circuitry. the device is turned on when en pin is set to logic high level. the characteristics of the low dropout voltage and low quiescent current make it suitabl e for low to medium power applications, for example, laptop computers , audio and video applications and battery powered devices. the typical quiescent current is approximately 6 0 a. built - in current - limit and thermal - shutdown functions prevent ic from damage in fault conditions. the ap7361c is available in u - dfn3030 - 8, sot89 - 5, sot223 , to252 and so - 8ep package s . features ? wide i nput v oltage r ange: 2. 2 v to 6.0 v ? output voltage accuracy: 1% ? very low d ropout voltage (3.3v): 36 0mv at 1a t ypical ? low quiescent c urrent (i q ): 6 0 a t ypical ? adjustable output voltage r ange: 0.8 v to 5.0v ? fixed output o ptions: 1 .0 v , 1.2v, 1.5v, 1.8v, 2.5v, 2.8v and 3.3v ? high psrr : 7 5 db @ 1khz ? current limit: 1.5a ? fold - b ack short circuit p rotection : 2 00ma ? thermal shutdown p rotection ? stable with mlcc, e - cap, tan - cap or solid c apacitor ? 2.2 f ? ambien t temperature r ange : - 40c to +85c ? available in green molding compound (no br, sb) ? totally lead - free & fully rohs compliant (notes 1 & 2) ? halogen and antimony free. green device (note 3) applications ? lcd - tv, monitor ? set - top - box ? home electrical appliances pin assignments ( top view ) ( top view ) u - dfn3030 - 8 sot89 - 5 ( top view ) ( top view ) sot223 sot223r ( top view ) ( top view ) so - 8ep so - 8epr ( top view ) ( top view ) to252 to252r note s: 1 . no purposely added lead. fully eu directive 2002/95/ec (rohs) & 2011/65/eu (rohs 2) compliant. 2. see http://www.diodes.com/quality/lead_free.html for more information about diodes incorporateds definitions of hal ogen - and antimony - free, "green" and lead - f ree . 3. halogen - and antimony - free "green products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total br + cl) and <1000ppm antimony compounds. 1 2 3 4 8 7 6 5 g n d o u t n c a d j / n c g n d e n n c i n n c 1 2 3 4 5 e n g n d a d j / n c i n o u t g n d 1 2 3 i n g n d o u t 1 2 3 g n d o u t i n i n n c n c n c e n o u t g n d n c 8 7 6 5 1 2 3 4 i n n c n c e n a d j / n c o u t n c g n d 8 7 6 5 1 2 3 4 1 2 3 i n g n d o u t 1 2 3 i n g n d o u t
ap7361c document number: ds 37274 rev. 2 - 2 2 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product typical applications circuit pin description s pin number pin name function u - dfn3030 - 8 sot89 - 5 to252 to252r sot223 sot223r so - 8ep so - 8epr 8 4 1 3 1 3 8 8 in the input of the regulator. bypass to ground through at least 1 f ceramic capacitor. 1 5 3 2 3 2 1 1 out the output of the regulator. bypass to ground through at least 2.2 f ceramic capacitor. for improved ac load response a larger capacitor is recommended . 4 2 2 1 2 1 4 3 gnd ground 3 3 C C C C C C C C C C C C C C C c o u t 4 . 7 f f i x e d v e r s i o n w i t h e n c i n 4 . 7 f i n g n d e n o u t e n a b l e v i n v o u t a p 7 3 6 1 c c o u t 4 . 7 f f i x e d v e r s i o n w i t h o u t e n c i n 4 . 7 f i n g n d o u t v i n v o u t a p 7 3 6 1 c c i n 4 . 7 f i n g n d e n o u t e n a b l e a d j r 2 r 1 c o u t 4 . 7 f v i n v o u t a p 7 3 6 1 c a d j u s t a b l e o u t p u t
ap7361c document number: ds 37274 rev. 2 - 2 3 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product functional block diagram i n e n g n d o u t g a t e d r i v e r 0 . 8 v c u r r e n t l i m i t a n d t h e r m a l s h u t d o w n f i x e d v e r s i o n w i t h e n r r i n g n d o u t g a t e d r i v e r 0 . 8 v c u r r e n t l i m i t a n d t h e r m a l s h u t d o w n f i x e d v e r s i o n w i t h o u t e n r r in en gnd adj out gate driver 0 . 8 v current limit and thermal shutdown adjustable versi on
ap7361c document number: ds 37274 rev. 2 - 2 4 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product absolute maximum ratings (@ t a = +25c, unless otherwise specified.) (note 4) symbol parameter rating unit v in input voltage 6.5 v C out, adj, en voltage v in +0.3 v t j operating junction temperature range - 40 to +150 c t st g storage temperature range - 65 to +150 c p d power dissipation internally limited by maximum junction temperature of +150c C p d power dissipation u - dfn3030 - 8 1700 mw to252 1250 sot223 1100 sot89 - 5 800 so - 8ep 1190 esd hbm human body model esd protection > 2 kv esd mm machine model esd protection (note 5) > 200 v note s : 4 . stresses greater than the 'absolute m aximum ratings' specified above may cause permanent damage to the device. these are stress ratings only; functional operation of the device at these or any other conditions exceeding those indicated in this specification is not im plied. device reliability may be affected by exposure to absol ute maximum rating condition s for extended periods of time. 5 . esd mm ratin g at 150v for en pin in sot89 - 5 package . recommended operating conditions (@ t a = +25c, unless otherwise specified.) s ymbol parameter m in m ax u nit v in input v oltage 2. 2 6.0 v v out out put voltage 0 . 8 5 . 0 v i out output current (note 6 ) 0 1.0 a t a operating ambient temperature - 40 +85 ? note : 6 . the device maintains a stable, regulated output voltage without a load current. when the output current is large, attent ion should be given to the limitation of the package power dissipation.
ap7361c document number: ds 37274 rev. 2 - 2 5 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product electrical characteristics ( @ t a = +25c, v in = v out + 1 v , c in = 4.7 f, c out = 4.7 f, v en = v in , unless otherwise specified.) symbol parameter test conditions min typ max unit v ref fb reference v oltage , adj pin i out = 10ma, t a = + 25 c 0.792 0.8 0.808 v i adj adj pin l eakage current C C 0.1 0.5 a i q input quiescent current enabled, i out = 0 a C 6 0 8 0 a i shdn input shutdown current v en = 0v, i out = 0 a - 1 0.05 1 a v out output voltage accuracy i out = 100ma, t a = +25 c 1.0v v out < 1.5v v out (s) - 0.015 v out (s) v out (s)+0 .015 v 1.5 v v out 3.5v v out (s)*0.99 v out (s) v out (s)*1 .01 line regulation v in = v out +1v to 5.5 v , i out = 100ma t a = +25 c C 0.01 0.1 %/v - 40 c t a +85 c C C 0.2 ? v out / v out load regulation i out from 1ma to 1a - 1.0 C 1.0 % v dropout dropout voltage (note 7 ) i out =300ma 1.0v v out < 1.1v C 710 750 mv 1.1v v out < 1.2v C 600 640 1.2v v out < 1.3v C 500 540 1.3v v out < 1.4v C 400 440 1.4v v out < 1.5v C 300 340 1.5v v out < 2.6v C 200 250 2.6v v out 3.5v C 100 150 i out =1a 1.0v v out < 1.1v C 840 C 1.1v v out < 1.2v C 780 C 1.2v v out < 1.3v C 700 C 1.3v v out < 1.4v C 650 C 1.4v v out < 1.5v C 600 C 1.5v v out < 2.0v C 570 C 2.0v v out < 2.6v C 440 C 2.6v v out 3.5v C 360 C v il en input logic low voltage C 0 C 0. 3 v v ih en input logic high voltage C 1. 0 C v in v r en pd en p ull - d own r esistor C C 3.0 C m ? i en en input leakage current v in = 5.5 v, v en = 0v - 0.1 C 0.1 a r pd output d ischarge r esistor v ol =1v C 100 C ? i ou t maximum o utput c urrent v in = v out +1v 1. 0 C C a i limit current limit v in = v out +1v ( v in mini =2.2v) 1.1 1.5 C a i short short - circuit current v in = v out +1v, output voltage < 1 5% v out C 400 C ma psrr power supply rejection ratio (note 8 ) f = 1 k hz, i out = 100ma C 75 C db f = 10 k hz, i out = 100ma C 55 C t st start - up time v out = 3v, c out = 2.2 f, r l = 30? C 150 C s output voltage temperature coefficient i out = 100ma, - 40 c t a +85 c C 1 0 0 C ppm/ c t shdn thermal shutdown threshold C C 150 C c t hys thermal shutdown hysteresis C C 20 C c ja thermal resistance junction - to - ambient u - dfn3030 - 8 (note 9 ) C 70 C c/w to252 (note 9 ) C 95 C sot223 (note 9 ) C 110 C sot89 - 5 (note 9 ) C 150 C so - 8ep (note 9) C 100 C notes : 7 . dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value. this parameter only applies to output voltages above 1. 2 v since minimum v in = 2.2v. 8 . for v in ? 2.5v and v in = v out + 1v. for v in < 2.5v, the psrr performance may be reduced. 9 . test condition : u - dfn3030 - 8 , so - 8ep device s are mounted on 2"x2", fr - 4 substrate pcb, with minimum recommended pad on top layer and thermal vias to bottom layer ground plane . to252 device s are mounted on 2"x2" fr - 4 substrate pc board, 2oz copper, with minim um recommended pad layout. for sot223 , t he device is mounted on fr - 4 substrate pc board, with minimum recommended pad layout. sot89 - 5 device s are mounted on 1"x1" fr - 4 substrate pc board, with minimum recommended pad layout . out in out v v v ? out a out v t v ?
ap7361c document number: ds 37274 rev. 2 - 2 6 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product performance characteristics v en = 0v to 2v (1v/div) v in = 4.0v v in = 4.7 f, c out = 2.2 f v out = 3v (1v/div) with 100ma load time (100 s/div) start - up time v en = 0v to 2v (1v/div) v in = 4.0v v in = 4.7 f, c out = 2.2 f v out = 3v (1v/div) with 500ma load time (100 s/div) start - up time v in = 2.2v to 3.2v (1v/div) t r = t f = 5 s i out = 100ma c out = 4.7 f v out = 1.2v (20mv/div) time (40 s/div) line transient response v in = 4.3v to 5.3v (1v/div) t r = t f = 5 s i out = 100ma c out = 4.7 f v out = 3.3v (20mv/div) time (40 s/div) line transient response v in = v en = 2.2v c in = c out = 4.7 f v out = 1.2v (20mv/div) i out = 50ma to 100ma (50ma/div) time (200 s/div) load transient response v in = v en = 2.2v c in = c out = 4.7 f v out = 1.2v (20mv/div) i out = 100ma to 500ma (200ma/div) time (200 s/div) load transient response
ap7361c document number: ds 37274 rev. 2 - 2 7 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product performance characteristics (cont.) v in = v en = 4.3v c in = c out = 4.7 f v out = 3.3v (20mv/div) i out = 50ma to 100ma (50ma/div) time (200 s/div) load transient response v in = v en = 4.3v c in = c out = 4.7 f v out = 3.3v (20mv/div) i out = 100ma to 500ma (200ma/div) time (200 s/div) load transient response v in = v en = 6.0v c in = c out = 4.7 f v out = 5.0v (20mv/div) i out = 50ma to 100ma (50ma/div) time (200 s/div) load transient response v in = v en = 6.0v c in = c out = 4.7 f v out = 5.0v (20mv/div) i out = 100ma to 500ma (200ma/div) time (200 s/div) load transient response
ap7361c document number: ds 37274 rev. 2 - 2 8 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product performan c e characteristics ( c ont.)
ap7361c document number: ds 37274 rev. 2 - 2 9 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product performance characteristics ( c ont.)
ap7361c document number: ds 37274 rev. 2 - 2 10 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product performance characteristics ( c ont.) application information input capacitor a 1 f ceramic capacitor is recommended between in and gnd pins to decouple input power supply glitch and noise. the amount of the capacitance may be increased without limit. this input capacitor must be located as close as possible to the device to assure inpu t stability and reduce noise. for pcb layout, a wide copper trace is required for both in and gnd pins. a lower esr capacitor type allows the use of less capacitance, while higher esr type requires more capacitance. output capacitor the output capacitor is required to stabilize and improve the transient response of the ldo. the ap7361c is stable with very small ceramic output capacitors. using a ceramic capacitor value that is at least 2.2f with 10m Q esr Q 300m on the output ensures stability . higher capacitance values help to improve line and load transient response. the output capacitance may be increased to keep low undershoot and o vershoot. output capacitor must be placed as close as possible to out and gnd pins.
ap7361c document number: ds 37274 rev. 2 - 2 11 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product application information ( c ont.) adjustable operation the ap7361c provides output voltage from 0.8 v to 5.0v through external resistor divider as shown below. the output voltage is calculated by: where v ref = 0.8v (the internal reference voltage) rearranging the equation will give the following that is used for adjusting the output to a particular voltage: to maintain the stability of the internal reference voltage, r2 need s to be kept smaller than 80 k ? . 1 f i n g n d e n o u t e n a b l e a d j r 2 r 1 4 . 7 f v i n v o u t a p 7 3 6 1 c a d j u s t a b l e o u t p u t ? ? ? ? ? ? ? ? ? ? 2 1 ref out r r 1 v v ? ? ? ? ? ? ? ? ? ? 1 v v r2 r1 ref out
ap7361c document number: ds 37274 rev. 2 - 2 12 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product application information ( c ont.) no load stability other than external resistor divider, no minimum load is required to keep the device stable. the device will remain stable an d regulated in no load condition. on/off input operation the on/off feature i s not available in the sot223 and to252 package s . the ap7361c is turned on by setting the en pin high, and is turned off by pulling it low. if this feature is not used, the en pin should be tied to in pin to keep the regulator output on at all time. to ensure proper operation, the signal source used to drive the en pin must be able to swing above and below the specified turn - on/off voltage thresholds listed in the electrical characteristics section under v il and v ih. current limit protection when output current at out pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to prevent over - current and to protect the regulator from damage due to overheating. short circuit protection when out pin is short - circuit to gnd, short circuit protection will be triggered and clamp the output current to approximately 200 ma. full current is restored w hen the output voltage exceeds 1 5% of v out . this feature protects the regulator from over - current and damage due to overheating. thermal shutdown protection thermal protection disables the output when the junction temperature rises to approximately +1 50 c, allowing the device to cool down. when the junction temperature reduces to approxi mately +1 30 c the output circuitry is enabled again. depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection circuit may cycle on and off. this cycling limits the heat dissipation of the regulator, protecting it from damage due to overheating. ultra fast start - up after enabled, the ap7361c is able to provide full power in as little as tens of microseconds, typically 200s , without sacrificing low ground current. this feature will help load circuitry move in and out of standby mode in real time, eventually extend battery life for mobile phones and other portable devices. low quiescent current the ap7361c , consuming only aro und 6 0 a for all input range, provides great power saving in portable and low power applications. power dissipation the device power dissipation and proper sizing of the thermal plane that is connected to the thermal pad is critical to avoid the rmal shutdown and ensure reliable operation. power dissipation of the device depends on input voltage and load conditions and can be calculated by: p d = (v in - v out ) i out the maximum power dissipation, handled by the device, depends on the maximum junction to ambient thermal resistance, maximum ambient temperature, and maximum device junction temperature, which can be calculated by the equation in the following: ja r ) a t - c 150 ( ) a (max@t p d ? ? ?
ap7361c document number: ds 37274 rev. 2 - 2 13 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product ordering information part number package code packaging 7 13 tape and reel ap7361c - xxfge - 7 fge u - dfn3030 - 8 30 00/tape & reel - 7 ap7361c - xxy 5 - 13 y5 sot89 - 5 25 00/tape & reel - 13 ap7361c - xxd - 13 d to252 25 00/tape & reel - 13 ap7361c - xxdr - 13 dr to252r 2500/tape & real - 13 ap7361c - xx e - 13 e sot 22 3 25 00/tape & reel - 13 ap7361c - xx er - 13 er sot223r 25 00/tape & reel - 13 ap7361c - xxsp - 13 sp so - 8ep 25 00/tape & reel - 13 ap7361c - xxspr - 13 spr so - 8epr 2500/tape & reel - 13 a p 7 3 6 1 c C x x x x x C x x o u t p u t p a c k a g e p a c k i n g b l a n k : a d j 1 0 : 1 . 0 v 1 2 : 1 . 2 v 1 5 : 1 . 5 v 1 8 : 1 . 8 v 2 5 : 2 . 5 v 2 8 : 2 . 8 v 3 3 : 3 . 3 v f g e : u - d f n 3 0 3 0 - 8 y 5 : s o t 8 9 - 5 d : t o 2 5 2 d r : t p 2 5 2 r e : s o t 2 2 3 e r : s o t 2 2 3 r s p : s o - 8 e p s p r : s o - 8 e p r 7 : 7 ' t a p e & r e e l 1 3 : 1 3 ' t a p e & r e e l
ap7361c document number: ds 37274 rev. 2 - 2 14 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product marking information (1) u - dfn3030 - 8 device package identification code ap7361c - adj u - dfn3030 - 8 sh ap7361c - 10 u - dfn3030 - 8 sj ap7361c - 12 u - dfn3030 - 8 sk ap7361c - 15 u - dfn3030 - 8 sv ap7361c - 18 u - dfn3030 - 8 sw ap7361c - 2 5 u - dfn3030 - 8 sx ap7361c - 2 8 u - dfn3030 - 8 sy ap7361c - 33 u - dfn3030 - 8 sz (2) sot89 - 5 device package identification code ap7361c - adj sot89 - 5 kr ap7361c - 10 sot89 - 5 ks ap7361c - 12 sot89 - 5 kt ap7361c - 15 sot89 - 5 ku ap7361c - 18 sot89 - 5 kv ap7361c - 25 sot89 - 5 kw ap7361c - 28 sot89 - 5 kx ap7361c - 33 sot89 - 5 kz x x : i d e n t i f i c a t i o n c o d e ( t o p v i e w ) x : i n t e r n a l c o d e x y x x w y : y e a r : 0 ~ 9 w : w e e k : a ~ z : 1 ~ 2 6 w e e k ; a ~ z : 2 7 ~ 5 2 w e e k ; z r e p r e s e n t s 5 2 a n d 5 3 w e e k 1 2 3 5 7 4 ( t o p v i e w ) x x y w x y : y e a r : 0 ~ 9 w : w e e k : a ~ z : 1 ~ 2 6 w e e k ; x : i n t e r n a l c o d e a ~ z : 2 7 ~ 5 2 w e e k ; z r e p r e s e n t s 5 2 a n d 5 3 w e e k x x : i d e n t i f i c a t i o n c o d e
ap7361c document number: ds 37274 rev. 2 - 2 15 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product marking information (c ont.) (3 ) to252 pin 1: in , pin 2: gnd, pin 3: out (4) sot223 pin 1: in , pin 2: gnd, pin 3: out (5) sot223 r pin 1: gnd, pin 2: out , pin 3: in 6 1 - v v ( t o p v i e w ) y y w w x x l o g o p a r t n u m b e r 6 1 - v v : 1 0 f o r 1 . 0 v 1 2 f o r 1 . 2 v 1 5 f o r 1 . 5 v 1 8 f o r 1 . 8 v 2 5 f o r 2 . 5 v 2 8 f o r 2 . 8 v 3 3 f o r 3 . 3 v x x : i n t e r n a l c o d e w w : w e e k : 0 1 ~ 5 2 , 5 2 r e p r e s e n t s y y : y e a r : 0 1 ~ 0 9 5 2 a n d 5 3 w e e k y w x 6 1 - v v l o g o x : i n t e r n a l c o d e ( t o p v i e w ) y : y e a r : 0 ~ 9 w : w e e k : a ~ z : 1 ~ 2 6 w e e k ; a ~ z : 2 7 ~ 5 2 w e e k ; z r e p e r s e n t s 5 2 a n d 5 3 w e e k p a r t n u m b e r 6 1 - v v : 1 0 f o r 1 . 0 v 1 2 f o r 1 . 2 v 1 5 f o r 1 . 5 v 1 8 f o r 1 . 8 v 2 5 f o r 2 . 5 v 2 8 f o r 2 . 8 v 3 3 f o r 3 . 3 v y w x 6 1 r - v v l o g o x : i n t e r n a l c o d e ( t o p v i e w ) y : y e a r : 0 ~ 9 w : w e e k : a ~ z : 1 ~ 2 6 w e e k ; a ~ z : 2 7 ~ 5 2 w e e k ; z r e p e r s e n t s 5 2 a n d 5 3 w e e k p a r t n u m b e r 6 1 r - v v : 1 0 f o r 1 . 0 v 1 2 f o r 1 . 2 v 1 5 f o r 1 . 5 v 1 8 f o r 1 . 8 v 2 5 f o r 2 . 5 v 2 8 f o r 2 . 8 v 3 3 f o r 3 . 3 v
ap7361c document number: ds 37274 rev. 2 - 2 16 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product marking information (c ont.) (6 ) to252 - r pin 1: gnd , pin 2: out , pin 3: in ( 7 ) so - 8ep pin 1: out , pin 2: en , pin s 3 , 5, 6 and 7 : nc, pin 4: gnd, pin 8: in ( 8 ) so - 8ep r pin 1: out , pin 2: adj/nc , pin 3 : gnd , pin s 4 , 6 and 7 : nc , pin 5 : en, pin 8: in 6 1 r - v v ( t o p v i e w ) y y w w x x l o g o p a r t n u m b e r 6 1 r - v v : 1 0 f o r 1 . 0 v 1 2 f o r 1 . 2 v 1 5 f o r 1 . 5 v 1 8 f o r 1 . 8 v 2 5 f o r 2 . 5 v 2 8 f o r 2 . 8 v 3 3 f o r 3 . 3 v x x : i n t e r n a l c o d e w w : w e e k : 0 1 ~ 5 2 , 5 2 r e p r e s e n t s y y : y e a r : 0 1 ~ 0 9 5 2 a n d 5 3 w e e k a p 7 3 6 1 c - v v ( t o p v i e w ) y y w w x x e l o g o p a r t n u m b e r a p 7 3 6 1 c - v v : 1 0 f o r 1 . 0 v 1 2 f o r 1 . 2 v 1 5 f o r 1 . 5 v 1 8 f o r 1 . 8 v 2 5 f o r 2 . 5 v 2 8 f o r 2 . 8 v 3 3 f o r 3 . 3 v s o - 8 e p w w : w e e k : 0 1 ~ 5 2 , 5 2 r e p r e s e n t s y y : y e a r : 0 8 , 0 9 . 1 0 ~ 5 2 a n d 5 3 w e e k x x : i n t e r n a l c o d e 1 4 8 5 7 3 6 1 c r - v v ( t o p v i e w ) y y w w x x e l o g o p a r t n u m b e r 7 3 6 1 c r - v v : b l a n k f o r a d j 1 0 f o r 1 . 0 v 1 2 f o r 1 . 2 v 1 5 f o r 1 . 5 v 1 8 f o r 1 . 8 v 2 5 f o r 2 . 5 v 2 8 f o r 2 . 8 v 3 3 f o r 3 . 3 v s o - 8 e p w w : w e e k : 0 1 ~ 5 2 , 5 2 r e p r e s e n t s y y : y e a r : 0 8 , 0 9 . 1 0 ~ 5 2 a n d 5 3 w e e k x x : i n t e r n a l c o d e 1 4 8 5
ap7361c document number: ds 37274 rev. 2 - 2 17 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product package outline dimensions (all d imensions in mm . ) please see ap02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. (1) package type: u - dfn3030 - 8 (type e) (2 ) package type: sot89 - 5 u - dfn3030 - 8 type e dim min max typ a 0.57 0.63 0.60 a1 0 0.05 0.02 a3 ? ? ? ? b 0.20 0.30 0.25 d 2.95 3.05 3.00 d2 2.15 2.35 2.25 e 2.95 3.05 3.00 e ? ? ? ? e2 1.40 1.60 1.50 l 0.30 0.60 0.45 z ? ? ? ? all dimensions in mm sot89 - 5 dim min max typ a 1.40 1.60 1.50 b 0.50 0.62 0.56 b1 0.44 0.54 0.48 c 0.35 0.43 0.38 d 4.40 4.60 4.50 d1 1.62 1.83 1.733 e 2.40 2.60 2.50 e - - 1.50 h 3.95 4.25 4.10 l 0.65 0.95 0.80 all dimensions in mm e h d1 b1 b e c l a d 8 (4x ) r0.200 l b (x8) e l (x8) a1 a3 z (x4) d d2 e2 e a
ap7361c document number: ds 37274 rev. 2 - 2 18 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product package outline dimensions (c ont.) (all d imensions in mm . ) please see ap02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. (3) package type: to252 (dpak) to252 (dpak) dim min max typ a 2.19 2.39 2.29 a1 0.00 0.13 0.08 a2 0.97 1.17 1.07 b 0.64 0.88 0.783 b2 0.76 1.14 0.95 b3 5.21 5.46 5.33 c 0.45 0.58 0.531 d 6.00 6.20 6.10 d1 5.21 - - e - - 2.286 e 6.45 6.70 6.58 e1 4.32 - - h 9.40 10.41 9.91 l 1.40 1.78 1.59 l3 0.88 1.27 1.08 l4 0.64 1.02 0.83 a 0 10 - all dimensions in mm b3 e l3 d l4 b2(2x) b(3x) e c a 7 1 h seating plane a1 gauge plane a 0.508 l 2.74ref d1 a2 e1
ap7361c document number: ds 37274 rev. 2 - 2 19 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product package outline dimensions ( c ont.) (all d imensions in mm . ) please see ap02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. (4) package type: sot223 (5) package type: so - 8ep sot223 dim min max typ a 1.55 1.65 1.60 a1 0.010 0.15 0.05 b 0.60 0.80 0.70 b1 2.90 3.10 3.00 c 0.20 0.30 0.25 d 6.45 6.55 6.50 e 3.45 3.55 3.50 e1 6.90 7.10 7.00 e - - 4.60 e1 - - 2.30 l 0.85 1.05 0.95 q 0.84 0.94 0.89 all dimensions in mm so - 8ep dim min max typ a 1.40 1.50 1.45 a1 0.00 0.13 - b 0.30 0.50 0.40 c 0.15 0.25 0.20 d 4.85 4.95 4.90 e 3.80 3.90 3.85 e0 3.85 3.95 3.90 e1 5.90 6.10 6.00 e - - 1.27 f 2.75 3.35 3.05 h 2.11 2.71 2.41 l 0.62 0.82 0.72 n - - 0.35 q 0.60 0.70 0.65 all dimensions in mm a1 a 7 7 d b e e1 b1 c e1 l 0 -10 q e 0.25 seating plane gauge plane 1 b e e1 a a1 9 (all side) 4 3 c q n 45 r 0.1 7 d e0 e l seating plane gauge plane f h exposed pad
ap7361c document number: ds 37274 rev. 2 - 2 20 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product suggested pad layout please see ap02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. (1) package type: u - dfn3030 - 8 (type e) (2) package type: sot89 - 5 (3) package type: to252 (dpak) dimensions value (in mm) c 0.65 c1 2.35 x 0.30 y 0.65 y1 1.60 y2 2.75 dimensions value (in mm) c 1.500 c1 1.050 x 0.680 x1 0.760 x2 1.930 x3 3.680 y 1.200 y1 1.200 y2 4.250 y3 4.500 dimensions value (in mm) c 4.572 x 1.060 x1 5.632 y 2.600 y1 5.700 y2 10.700 x3 x y y3 x1 x2 c y2 y1 c1 x1 x y2 y1 y c y (x8) x (x8) c c1 y1 y2
ap7361c document number: ds 37274 rev. 2 - 2 21 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product suggested pad layout (cont.) please see ap02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. (4) package type: sot223 (5) package type: so - 8ep dimensions value (in mm) c 2.30 c1 6.40 x 1.20 x1 3.30 y 1.60 y1 1.60 y2 8.00 dimensions value (in mm) c 1.270 x 0.802 x1 3.502 x2 4.612 y 1.505 y1 2.613 y2 6.500 x1 y1 y x c c1 y2 c y1 x1 x y y2 x2
ap7361c document number: ds 37274 rev. 2 - 2 2 2 of 22 www.diodes.com september 2015 ? diodes incorporated ap 7361c advance information new product important notice diodes incorporated makes no warranty of any kind, express or implied, with regards to this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose (and their equivalents under the laws of any jurisdiction). diodes incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other c hanges without further notice to this document and any product described herein. diodes incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does diodes incorporated convey any license unde r its patent or trademark rights, nor the rights of others. any customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold diodes incorporated and all the companies whose products are represented on diod es incorporated website, harmless against all damages. diodes incorporated do es not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. should customers purchase or use diodes incorporated products for any unintended or unauthorized application, customers shall indemni fy and hold diodes incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising ou t of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized applicat ion. products described herein may be covered by one or more united states, international or foreign patents pending. product nam es and markings noted herein may also be covered by one or more united states, international or foreign trademarks. this doc ument is written in english but may be translated into multiple languages for reference. only the english version of this do cument is the final and determinative format released by diodes incorporated. life support diodes incorporated products are speci fically not authorized for use as critical components in life support devices or systems without the express written approval of the chief executive officer of diodes incorporated. as used herein: a. life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided i n the labeling can be reasonably expected to result in signifi cant injury to the user. b. a critical component is any component in a life support device or system whose failure to perform can be reasonably expe cted to cause the failure of the life support device or to affect its safety or effectiveness. c ustomers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support de vices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety - related requireme nts concerning their products and any use of diodes incorporated products in such safety - critical, life support devices or systems, notwithstanding any devices - or systems - related information or support that may be provided by diodes incorporated. further , customers must fully indemnify diodes incorporated and its representatives against any damages arising out of the use of diodes incorporated products in such safety - critical, life support devices or systems. copyright ? 201 5 , diodes incorporated www.diodes.com

▲Up To Search▲

Price & Availability of AP7361C-10

	To Download AP7361C-10 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .